OPPO A37m Flash file & Hang on LOGO Fix New Method.2023
Once you have all of the required items, follow these steps.
- Download and install the infinity-Box CM2 drivers on your computer.
- Connect the OPPO A37m to your computer using the USB cable.
- Turn on the OPPO A37m and put it into Download mode. To do this, press and hold the Volume Down button and the Power button at the same time.
- Open the infinity-Box CM2 software and select the "MTK" tab.
- Click on the "Read Firmware" button and select the OPPO A37m firmware file that you downloaded earlier.
- Use CM2 Click EMI file preloader_oppo6750_15127.bin
- Click Only UserData File Use
- Click on the "Write Firmware" button and wait for the process to complete.
- Once the process is complete, disconnect the OPPO A37m from your computer and turn it on. The OPPO A37m should now boot up normally.
 |
| 1 Steps |
 |
| 2 Steps |
OPPO A37m MT6755 hang-on logo issue Fix using infinity-Box CM2-2023
1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...
PTFN : MediaTek USB Port_V1633 (COM8)
MODE : BOOTROM
PORT : 8
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
CHIP : MT6755 , SBID : 0x8A00 , HWVR : 0xCB00 , SWVR : 0x0001
TYPE : MODERN RAPHAEL
BROM : MEID : 254B108E8504149EC21473F08377FF6E
BROM : SecLevel : 0x00000000
BROM : SecMode : PLAIN [+PRL]
BROM : BROM|BL : 0x05|0xFE
BROM : BOOTROM
MODE : 0_base : base_v2216 | Manual : Enabled
AGENT : Look for suitable BootChain in DA ...
AGENT : MTK_AllInOne_DA.bin
AGENT : Found MT6755
AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
DA : SYNC
DA : MODE : BROM
DA : EXT_RAM NOT initialized!
EMI : DEV : MT6755
EMI : SRC : preloader_oppo6750_15127.bin
EMI : CNT : 0004
EMI : [00] : eMMC : DDR3 : ID : 150100514531334D42 : VEN : SAMSUNG | DEV : QE13MB : RAM : [ 2.00 GB ]
EMI : [01] : eMMC : DDR3 : ID : 90014A484147346132 : VEN : HYNIX | DEV : HAG4a2 : RAM : [ 2.00 GB ]
EMI : [02] : eMMC : DDR3 : ID : 13014E51324A393652 : VEN : MICRON | DEV : Q2J96R : RAM : [ 2.00 GB ]
EMI : [03] : eMMC : DDR3 : ID : 150100524531424D42 : VEN : SAMSUNG | DEV : RE1BMB : RAM : [ 3.00 GB ]
EMI : Init EMI from PRELOADER
EMI : EXT_RAM CFG Passed!
DA : BOOT to 2nd DA ...
DA : 2ND stage confirmed!
DA : SYNC with DA passed!
DA : Receiving HW info
SRAM: 0x00038000 [ 224.00 KB ]
DRAM: 0x80000000 [ 2.00 GB ]
EMMC: 13014E51324A39365210033D10DB3F1
EMMC: VEN : MICRON | OEM : 4E01 | DEV : Q2J96R
EMMC:
BOOT1 : 0x00400000 [ 4.00 MB ]
BOOT2 : 0x00400000 [ 4.00 MB ]
RPMB : 0x00400000 [ 4.00 MB ]
USER : 0x3AB400000 [ 14.68 GB ]
CHIP : MT6750 , SBID : 0x8A00 , HWVR : 0xCB00 , SWVR : 0x0000 , EVOL : 0x0000
RNID : 11C01BB6E9FBF6C5870BAF4545A42982
DA : USB : FULL-SPEED
DA : USB : Change Port Speed
PTFN : MediaTek DA USB VCOM (Android) (COM30)
MODE : PRELOADER PORT
PORT : 30
Boot done!
0 Comments: